Campbell Hausfeld WL6502 Uživatelský manuál stáhnout pdf (Strana 2)

Assembly

HANDLE ASSEMBLY (Figure 1)

1. Place ends of handle into handle inserts

on sides of tank.

2. Assemble four (4) screws (from parts

package) through holes in handle.

Never use

the

handle to lift the unit completely off

the ground. Only use the handle to lift

one end so the wheels may be used to

move the unit.

WHEEL ASSEMBLY (Figure 2)

Wheel assembly kit includes:

- 2 wheels*

- 2 axle bolts*

- 2 lock washers*

- 2 nuts*

The items marked with an asterisk (*)

were shipped loose with the unit.

1. Wheel has an offset hub. With offset

hub facing axle iron, assemble axle

bolt through holes in wheel and axle

iron.

2. Follow all local electrical and safety

codes, as well as in the U.S.A.,

National Electrical Codes (NEC) and

Occupational Safety and Health Act

(OSHA).

3. Only persons well acquainted with

these rules of safe operation should

be allowed to use the compressor.

4. Keep visitors away and NEVER allow

children in the work area.

5. Wear safety glasses and

use hearing protection

when operating the pump

or unit.

6. Do not stand on or use the pump or

unit as a handhold.

7. Before each use, inspect compressed

air system and electrical components

for signs of damage, deterioration,

weakness or leakage. Repair or

replace defective items before using.

8. Check all fasteners at frequent

intervals for proper tightness.

Motors, electrical equipment

and controls can cause

electrical arcs that will ignite

a flammable gas or vapor. Never

operate or repair in or near a

flammable gas or vapor. Never store

flammable liquids or gases in the

vicinity of the compressor.

Compressor parts may be hot

even if the unit is stopped.

9. Keep fingers away from a running

compressor; fast moving and hot

parts will cause injury and/or burns.

10. If the equipment should start to

abnormally vibrate, STOP the

engine/motor and check

immediately for the cause. Vibration

is generally a warning of trouble.

11. To reduce fire hazard, keep

engine/motor exterior free of oil,

solvent, or excessive grease.

Never

remove

or attempt to adjust safety valve. Keep

safety valve free from paint and other

accumulations.

Operating Instructions

Never attempt to repair or

modify a tank! Welding,

drilling or any other

modification will weaken the tank

resulting in damage from rupture or

explosion. Always replace worn or

damaged tanks.

Drain liquid from tank daily.

12. Tanks rust from moisture build-up,

which weakens the tank. Make sure

to drain tank daily and inspect

periodically for unsafe conditions

such as rust formation and corrosion.

13. Fast moving air will stir up dust and

debris which may be harmful.

Release air slowly when draining

moisture or depressurizing the

compressor system.

SPRAYING PRECAUTIONS

Do not spray flammable

materials in vicinity of open

flame or near ignition

sources including the compressor unit.

14. Do not smoke when spraying paint,

insecticides, or other flammable

substances.

15. Use a face mask/

respirator when spraying

and spray in a well

ventilated area to

prevent health and fire hazards.

16. Do not direct paint or other sprayed

material at the compressor. Locate

compressor as far away from the

spraying area as possible to

minimize overspray accumulation

on the compressor.

17. When spraying or cleaning with

solvents or toxic chemicals, follow

the instructions provided by the

chemical manufacturer.

Risk of electrical shock. Turn

off and unplug before

servicing. Service should be performed

by an authorized service center.

www.chpower.com

General Safety (Con’t)

Figure 1 - Handle Assembly

Screws

Figure 2 - Wheel Assembly

Axle bolt

Wheel

Lock washer

Nut

1 2 3 4 5 6 7 ... 23 24

Komentáře k této Příručce

Žádné komentáře

Campbell Hausfeld WL6502 Uživatelský manuál Strana 2

Komentáře k této Příručce

Související produkty a manuály pro Vzduchové kompresory Campbell Hausfeld WL6502