Campbell Hausfeld WL6502 Uživatelský manuál stáhnout pdf (Strana 3)

providing an escape wire for electric

current. This product is equipped

with a cord having a grounding wire

with an appropriate grounding plug.

Cord must be plugged into an outlet

that is properly installed and

grounded in accordance with all local

codes and ordinances.

Improper use of grounding

plug can result in a possible

risk of electrical shock!

Do not

use a

grounding adapter with this product!

2. If repair or replacement of cord or

plug is necessary, do not connect

grounding wire to either flat blade

terminal. The wire with insulation

having an external surface that is

green (with or without yellow

stripes) is the grounding wire.

Never

connect

green (or green and yellow) wire to a

live terminal.

3. Check with a qualified electrician or

serviceman if grounding instructions

are not completely understood, or if

in doubt as to whether product is

properly grounded. Do not modify

plug provided; if it will not fit outlet,

have proper outlet installed by a

qualified electrician.

WIRING

1. Local electrical wiring codes differ

from area to area. Source wiring,

plug and protector must be rated for

at least the amperage and voltage

indicated on motor nameplate, and

meet all electrical codes for this

minimum.

2. Use a slow blow fuse or a circuit

breaker.

Overheating, short circuiting and fire

damage will result from inadequate

wiring, etc.

NOTE: 120 volt, 15 amp units can be

operated on a 120 volt circuit under the

following conditions:

a. No other electrical appliances

or lights are connected to the same

branch circuit.

b. Voltage supply is normal.

c. Circuit is equipped with a 15

amp circuit breaker or a 15

amp slow blow fuse.

3. If these conditions cannot be met or

if nuisance tripping of current

protection device occurs, it may be

necessary to operate compressor

from a 120 volt, 20 amp circuit.

2. Place lock washer on axle bolt. Then

tighten nut securely to threaded part

of axle bolt.

3. Repeat procedure with other side.

LOCATION

The tank must sit level or slope slightly

towards the drain valve to allow the

tank to drain properly.

It is extremely important to install the

compressor in a clean, well ventilated

area where the surrounding air

temperature will not be more than 100°F.

A minimum clearance of 18 inches

between the compressor and a wall is

required because objects could obstruct

air flow.

Do not

locate the

compressor air inlet near steam, paint

spray, sandblast areas or any other

source of contamination. This debris

will damage the motor.

ELECTRICAL INSTALLATION

All

wiring

and electrical connections should be

performed by a qualified electrician.

Installation must be in accordance with

local codes and national electrical codes.

Never use an extension cord

with this product. Use

additional air hose instead of

an extension cord to avoid power loss

and permanent motor damage. Use of

an extension cord voids the warranty.

GROUNDING INSTRUCTIONS

1. This product is for use on a nominal

120 volt circuit and has a grounding

plug that looks like the plug

illustrated in Figure 3. Make sure the

product is connected to an outlet

having the same configuration as the

plug. Do not use an adapter with this

product. This product must be

grounded. In the event of an

electrical short circuit, grounding

reduces risk of electrical shock by

MOISTURE IN COMPRESSED AIR

Moisture in compressed air will

form into droplets as it comes from

an air compressor pump. When

humidity is high or when a

compressor is in continuous use for

an extended period of time, this

moisture will collect in the tank.

When using a paint spray or

sandblast gun, this water will be

carried from the tank through the

hose, and out of the gun as droplets

mixed with the spray material.

IMPORTANT: This condensation

will cause water spots in a paint

job, especially when spraying other

than water based paints. If

sandblasting, it will cause the sand

to cake and clog the gun,

rendering it ineffective. A filter in

the air line (MP3105), located as

near to the gun as possible, will

help eliminate this moisture.

TEST

RESET

Grounded Outlet

Grounded

Figure 3

www.chpower.com

STOP!

Installation

Assembly (Continued)

Oilless Compressors

1 2 3 4 5 6 7 8 ... 23 24

Komentáře k této Příručce

Žádné komentáře

Campbell Hausfeld WL6502 Uživatelský manuál Strana 3

Komentáře k této Příručce

Související produkty a manuály pro Vzduchové kompresory Campbell Hausfeld WL6502